Pozitif Yönde Dönen Saat ?
-
Arap saatleri normalde terstir...
-
Stigma müridem,
aslında resimle anlatılan yöntem olur
fakat bir şey eksik anlatılmış sanırım.
o sarı sargı ( bobin) elektro mıknatıs oluyor
sol tarafı N ise sağ tarafı S kutup yani
O bobin ordan çıkarılıp terrs takılırısa ( solu sağa , sağı sola getirebilirsen ) kablo elektronik bağlantı müsade ederse olur ..
ya da bir elektronik tamirciye yaptırtabilirsin
izmirde olsaydım yardımcı olurdum... :((
-
Ben aliağa da oturuyorum o dediğiniz saatçi kahvenin yanındaki mi? Baya eski bi yer orası...
-
ltcelik bunu yazdı:
-----------------------------Stigma müridem,
aslında resimle anlatılan yöntem olur
fakat bir şey eksik anlatılmış sanırım.
o sarı sargı ( bobin) elektro mıknatıs oluyor
sol tarafı N ise sağ tarafı S kutup yani
O bobin ordan çıkarılıp terrs takılırısa ( solu sağa , sağı sola getirebilirsen ) kablo elektronik bağlantı müsade ederse olur ..
ya da bir elektronik tamirciye yaptırtabilirsin
izmirde olsaydım yardımcı olurdum... :((
-----------------------------havya yardımı ile kablolar değiştirilse bu mümkün hale gelmezmi.. yani bobin için
-
http://www.enilginc.com/pinfo.asp?pid=144
Ters Saat
Geçen zamanı geri getirebilmek ancak bu saatle mümkün olabilirdi. Rakamları ters yerleştirilmiş bu duvar saatinin akrep ve yelkovanı da "herkesin gittiği yoldan" gitmiyor, ufak çaplı bir Benjamin Button tribi yaşatıyor... Ürün Kodu : Backwards Clock Fiyatı : 44,90 TL Kdv Dahil Fiyatı : 44,90 TL Havale İnd. (%5) : 42,66 TL Stok Durumu : Stoklarımızda Güncelleme Tarihi : 09.08.2009 23:35:00 -
muhammedonur bunu yazdı:
-----------------------------
This is a travel clock that you can set an alarm. In my experience with 3 or 4 different clocks with similar mechanisms the plate can be reversed to make the clock run counter-clockwise.
I use the scissors to place the clock shaft in the middle so it doesn't press on the gears while I work. The first thing is to get the back off of the clock to expose the gears. A small standard screwdriver is a good choice. Don't forget to take the small black knobs off the time adjustment wheel. If you don't they will shoot off as you pry the back cover of the clock.
Study the way this looks and remove parts slowly as you learn. The left most gear is minutes, the middle is seconds and the right and smallest gear below work together to calculate the second hand movement. The smallest gear turn approximately 180 degrees each second. Unfortunately, it is complicated to watch the clock with the cover removed as it requires an alignment hole to be in place on the cover side.
The gears simply pull straight up and out and you can set them down in order as you go. The focus is on the orientation of the plate inside the copper wound electromagnet. As you work the plate up and off of the pins that hold it in place, take care not to pull at the copper wound mechanism. The plate should slide out of a plastic rectangle slot, the copper is not wrapped around the plate itself.
This is the original orientation of the plate.
Some plates can be pulled out, flipped 180 degrees and be replaced, done. When it doesn't work like that, I nip off about 3/32 at a 45 degree angle as shown.
As you can see the plate is restored and it fits over the guide pins.
Take care when replacing the cover that the smallest gear is pointing straight up as much as possible to align it for the cover. When the cover is replaced it won't smash the shaft. If the shaft gets smashed they might weaken too much to be straightened again. During this mod one of the wires came off underneath the copper winding and the clock wouldn't work, so I soldered and reassembled.Kaynak: http://backwardstime-moddy.blogspot.com/ en güzel bura anlatmış sanırım.
-----------------------------bu olay kesin çalışıyor. geçen sene 2 saate uyguladım tıkır tıkır çalışıyo. zaten benim sitede vercektim yapılışını kısa bi süre sonra.
yazıcıdanda sayıları ters yönde çıkartıp koyarssan arkasına gerçek saati gösterir ama ters yönde döner.
-
HeadBanger bunu yazdı:
-----------------------------
ltcelik bunu yazdı:
-----------------------------Stigma müridem,
aslında resimle anlatılan yöntem olur
fakat bir şey eksik anlatılmış sanırım.
o sarı sargı ( bobin) elektro mıknatıs oluyor
sol tarafı N ise sağ tarafı S kutup yani
O bobin ordan çıkarılıp terrs takılırısa ( solu sağa , sağı sola getirebilirsen ) kablo elektronik bağlantı müsade ederse olur ..
ya da bir elektronik tamirciye yaptırtabilirsin
izmirde olsaydım yardımcı olurdum... :((
-----------------------------havya yardımı ile kablolar değiştirilse bu mümkün hale gelmezmi.. yani bobin için
-----------------------------Olur tabii.. Belki müride kardeşimizde havye yoktur diye ööle dedim, Lehim yapabiliyorsa sadece bobinin uçlarını değiştirse yeter..
Ama kablo bağlantısı müsade ederse lehime de gerek yok
-
him ilginç denemek lazım (:
-
aslında çalıma mantığı çok ilginç.sadece bobinin içindeki metalin yönünü deiştirerek nasıl kutupları değiştiriyoruz çözemedim.sonuçta aynı şekli alıyor metal bölüm.ordaki metallerin ayrı bir manyetikliği yok.
bobin metali manyetik hale getiriyor.manyetik hale gelen metalin ucundaki yuvarlak kısımda bulunan demire bağlı dişliyi ileri geri hareket ettirip diğerlerini döndürüyor.basitçe mantığı böyle ama manyetiklik nasıl değişir bu durumda anlayamadım.
-
metalin yönünü cevirdiğinde bir şey olmaz sanrım..önemli olan bobinin kutuplarını değiştirmek..